Shure PGX14/Beta98H wireless instrument microphone system

Shure PGX14/BETA98H System Features:

• A convenient and versatile wireless system for instrument applications, such as saxophone, woodwinds, strings, and percussion
• The WB98H/C features transformerless preamplifier circuitry, which improves linearity across the full frequency range
• The pickup pattern of the Beta 98H/C provides high gain-before-feedback and excellent rejection of unwanted noise
• High maximum sound pressure level (SPL) enables the WB98H/C to handle the extreme demands of brass, woodwind and percussion instruments
• The Frequency Agile UHF design provides up to 90 selectable UHF frequencies that operate on an 18MHz UHF bandwidth
• Diversity Reception system uses twin receiver circuits to minimise noise and drop out caused by RF interference
• Hi quality sound with quick and easy setup using infrared remote synchronization of channel and frequency status
• Use 9 systems simultaneously within the 846 - 865 Mhz range for big events
• PGX4 has XLR and unbalanced 1/4 inch jack audio outputs
• PGX1 includes battery power warning lights - 8 hours battery life from 2 x AA 1.5v alkaline batteries
• Carry case and batteries included
• The PGX Series System is expandable as the WB98H/C can be simply unplugged and replaced with any other Shure Microphone that has a 4-pin mini connector or any other line /mic or guitar signal using the optional WA302 and WA310 cables

Shure PGX14/BETA98H System Specifications:

• Working Range: 100m (300 ft.) Note: actual range depends on RF signal absorption, reflection, and interference
• Audio Frequency Response +/– 2 dB: Minimum: 45 Hz, Maximum: 15 kHz (Overall system frequency depends on microphone element.)
• Dynamic Range: 100 dB A-weighted

Shure WB98H/C Specifications:

• Type: Condenser (electret bias)
• Frequency Response: 20 to 20,000 Hz
• Polar Pattern: Supercardioid (as supplied), uniform with frequency, symmetrical about axis. Cartridge for cardioid polar pattern also available.
• Output Level (at 1,000 Hz): -59 dBV/Pa* (1 mV) typical *1 Pa = 94 dB SPL
• Maximum SPL - 2.5 kilohm load: 160 dB, 1 kilohm load: 156 dB
• Preamplifier Output Clipping Level: 2.5 kilohm load: + 6 dBV (2.0 V), 1 kilohm load: + 2 dBV (1.26 V)
• Dynamic Range (maximum SPL to A-weighted noise level): 125 dB
• Output Noise (equivalent SPL): 35 dB typical, A-weighted
• Signal-to-Noise Ratio: 59 dB at 94 dB SPL (IEC 651)
• Output Impedance - Rated at 150 ohms (actual). Recommended minimum load impedance: 1 kilohm
• Net Weight: Microphone: 12 g (0.4 oz) less cable
• Cable: Black 10 ft. cable terminated to 4-Pin Mini-Connector (miniature connector type TA4F)
• Supplied with a snap-on windscreen, a storage bag, a gooseneck angle brace, and a cable management device

Shure PGX1 Specifications:

• Audio Input Level: -10 dBV maximum at "mic" gain position, +10 dBV maximum at 0dB gain position, +20 dBV maximum at -10dB gain position
• Gain Adjustment Range: 30 dB
• Input Impedance 1 M Ohm
• RF Transmitter Output: 30 mW maximum (dependent on applicable country regulations)
• Dimensions 108 mm H x 64 mm W x 19 mm D (4.25 x 2.50 x 0.75 in.)
• Weight: 81 grams (3 oz.) without batteries
• Housing: Molded polycarbonate case
• Power Requirements: 2 AA size alkaline or rechargeable batteries
• Battery Life: Around 8 hours (alkaline)

Shure PGX4 Specifications:

• Dimensions: 40 mm H x 181 mm W x 104 mm D (1.6 x 7.125 x 4.1 in.)
• Weight: 327 g (11.5 oz.)
• Housing: ABS
• Audio Output Level (Ref. +/– 33 kHz deviation with 1kHz tone): XLR connector (into 600 Ohm load): –19 dBV, 1/4 inch connector (into 3000 Ohm load): –5 dBV
• Output Impedance: XLR connector: 200 Ohm, 1/4 inch connector: 1kOhm
• XLR output: Impedance balanced, Pin 1: Ground (cable shield), Pin 2: Audio, Pin 3: No Audio
• Sensitivity: –105 dBm for 12 dB SINAD, typical
• Image Rejection: 70 dB, typical
• Power Requirements: 12–18 Vdc at 150 mA, supplied by external power supply